Simplicity 1693756 Operator's Manual

ATTACHMENTOPERATOR’SMANUALSnow Plow/Dozer BladeMfg. No. Description1693754 42” Remote Angling Snow Plow/Dozer BladeHitchMfg. No. Description1693756 Hi

9Initial Setup & AssemblyRef Qty Description1 1 ROD, Control Handle, Upper2 6 NUT, Hex, 5/16-183 2 LOCKWASHER, 5/164 4 WASHER, 5/165 2 CAPSCREW, 5

10Initial Setup & Assembly2135678101617182830312928121314153299911202223242526271921994433433434335363738413742403739NOTE: The dashed-line rod:Lan

11Initial Setup & AssemblyINITIAL SETUP & ASSEMBLYNOTE: Some of the following setup procedures mayalready be completed.Assemble Blade1. Place

12Initial Setup & AssemblyInstall Rear Push Bar SupportNOTE: Manual Lift Models-If your tractor is not alreadyequipped with a Large Lift Lever kit

13Initial Setup & AssemblyFigure 15. Install Push Bar AssemblyA. Push Bar Assembly C. Clevis PinsB. Hitch D. Safety ClipsFigure 14. Installing H

14Initial Setup & AssemblyInstall Spring Assist Bracket (Baron/Broadmoor/1600/2600 Models Only)NOTE: Spring-assist bracket assembly (Figure 16) do

15Initial Setup & AssemblyInstall Lift RodNOTE: Two lift rods are packaged with theBroadmoor/LT/1600/2600 & Landlord/GT/1700/2700hitch assembl

16Initial Setup & AssemblyFigure 23. Control Rod SupportA. SupportB. 5/16-18 x 1-1/2 CapscrewsC. 5/16 Centerlock NutsD. 5/16 Plain WashersE. Spac

17Removing &Attaching the Hitch & BladeREMOVAL & INSTALLATIONRemoving & Attaching Dozer Blade1. Lower the blade. Put the lift lever i

18Removing & AttachingRemoving & Attaching Hitch1. Remove the safety clip (A, Figure 26) and remove thehitch pin (D).2. Lift the hitch bar (B)

1Table of ContentsAdjustments...7Skid Shoe Adjustment ...7Spri

19Reinforcement Bracket InstallationINSTALL REINFORCEMENTBRACKETNOTE: This kit applies to the Landlord / 1700 / 2700Series hydraulic lift models only.

Torque Specification ChartFOR STANDARD MACHINE HARDWARE (Tolerance ± 20%)HardwareGradeSAE Grade 2 SAE Grade 5 SAE Grade 8Size Of in/lbs in/lbs in/lbs

Simplicity Mfg. Inc.500 N Spring Street / PO Box 997Port Washington, WI 53074-0997 USA© Copyright 2001 Simplicity Manufacturing, Inc.All Rights Rese

OPERATING SAFETYO Always clear snow up and down the face of slopes,never across the face. Exercise extreme cautionwhen changing direction on slopes. D

3TRACTOR CONTROLSBefore you begin operating the tractor with the dozerblade attachment, make certain you have:• Read and understood the instructions i

4Checks Before Starting1. Refer to the Maintenance & Adjustments sections ofthis manual and perform any needed service. Also,refer to the tractor

5General Operating InstructionsDaily Storage1. Allow tractor engine to cool before storing in anyenclosure.2. After dozing or plowing jobs are complet

6MaintenanceSchedule For Normal CareCare Required ScheduleClean debris from After each use.dozer blade.Lubricate dozer blade. Every 10 hours or at lea

7AdjustmentsSkid Shoe AdjustmentSlotted holes are provided to permit adjustment of theshoe assemblies for raising and lowering the blade tovarious wor

8AdjustmentsFigure 6. Adjusting Lift RodA. Front Set CollarB. Rod GuideC. SpringD. Rear Set CollarE. Spring ClipFigure 7. Lift Lever Quadrant - Side