Simplicity Clean Sweep Twin Catcher Operator's Manual

Print VendorInstructionsHow to use this fileOperator’s ManualsPaper Size: • 11x17• Body - 50 lbs brilliant white offset or equivalent• Cover - on pre-

6Normal Installation & Removal3. Open grass bag cover and install grass bag frames(A, figure 3) to support brackets (B).4. On 30" mower, lift

7TroubleshootingThe following table provides troubleshooting instructionsfor the more common and easily corrected problems. Forproblems not covered in

8Initial Setup & Assembly30” MODELS - BLADE AND ADAPTER ASSEMBLYBlade Assembly - 30” Mower1. Remove the mower deck to access the blade orusing an

9Initial Setup - 30” Models3. Install 5/16-18 x 2-1/4 carriage bolt (A, figure 8)through front hole in mower deck along with cup (B),whiz flange nut (

10Initial Setup - 34” Models34" MODELS - BAFFLE, BLADE, & ADAPTERASSEMBLYInstall Baffle1. Remove mower deck from rider. Position mower deckup

11Initial Setup - 34” ModelsInstall Blades - Early Models with Splined Arbor1. Remove existing discharge-side blade but retainhardware. Remove the ret

12Initial Setup - All ModelsFRAME & BAGGER SUPPORTASSEMBLY - ALL MODELSNote: Units with 0510 transmissions use anchors (A, fig-ure 13) with a notc

13Initial Setup - All ModelsGRASS CATCHER ASSEMBLY - ALL MODELSNOTE: Cover and bag support are packaged as anassembly with long clevis pins and clips.

14Initial Setup - All Models5. Open cover and fasten cable (A, figure 17) to tubesupport (B) to prevent cover from going over centerwhen opened. Loop

15Initial Setup - All Models7. Apply dry talc powder to rubber seal at cover open-ing. Install tube (A, figure 19) as far as possible intoopening to c

THIS PAGE INTENTIONALLY BLANK(FOR PLACEMENT ONLY - DO NOT PRINT)

InstallationInstructionsBaffle KitPart No. 1686783INSTALLATION1. Remove the hardware (D) securing the plastic elbow(C) to the metal support plate (B).

INSTALLATION INSTRUCTIONSEXHAUST SHIELD KITMFG. NO. 16666101.Raise the seat deck to expose the right-hand topduct.2.See figure 1. Cut out the template

18Torque Specification ChartFOR STANDARD MACHINE HARDWARE (Tolerance ± 20%)HardwareGradeSAE Grade 2 SAE Grade 5 SAE Grade 8Size Ofin/lbs in/lbsin/lbs

OPERATOR’SMANUALClean Sweep Twin Catchers Mfg. No. Description1692149 Clean Sweep Twin Catcher (for 30” Mower Decks)1692150 Clean Sweep Twin Catcher (

MANUFACTURING, INC.500 N Spring Street / PO Box 997Port Washington, WI 53074-0997www.simplicitymfg.com© Copyright 2004 Simplicity Manufacturing, Inc

1Table of ContentsNormal Installation & RemovalInstallation & Removal ...5TroubleshootingChart...

2Safety Rules& InformationRead these safety rules and follow them closely. Failure to obey these rules could result in loss of control ofunit, sev

3BEFORE OPERATIONClear the lawn of all sticks, stones, wire and other debriswhich may be caught or thrown by the mower blades.Check grass condition. I

4Operation &StorageBEFORE OPERATIONClear the lawn of all sticks, stones, wire and other debris,which may be caught or thrown by the mower blades.C

5Normal Installation &RemovalINSTALLATION & REMOVALNOTE: For first-time installation, refer to Initial Setup &Installation.NOTE: If mower