Simplicity Synergy X9 Specifications Page 144
- Page / 352
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Synergy Nano Technical Manual, Revision -
Page 144
Alarms
The alarm screen displays any Synergy Nano
alarm conditions. Access this screen to view
and clear a chamber alarm. When an alarm
occurs, the following attributes are listed.
♦ Time of Alarm
♦ Alarm Type
♦ Ack: User acknowledgement of alarm.
♦ Cleared: Indicates if the alarm condition
has cleared.
The word ALARM will flash in the upper right
corner of all screens while an alarm condition
exists.
Press the Ack Alarm button to acknowledge an alarm. This will set the Ack column value to Yes. When the
Alarm condition clears the Cleared column will automatically be set to Yes. When both the Ack and Cleared
column read Yes (When the user has acknowledged the alarm and the alarm condition has cleared), the
alarm is removed from the list. Specific alarms are covered in greater detail in the following section.
7.2 Alarm Functions
This section contains information on: Low Storage Alarms, Low Memory Alarms and Alarm Actions (Relays,
Alarm Indications, and Outputs). Note: Alarm Relays are normally energized.
SYNERGY NANO ALARMS AND ACTIONS
ALARM RESPONSES
# Alarm Name
Alarm
Relay 1
Alarm
Relay 2
Alarm On
Screen Flashes
All Outputs
Turn OFF
1 Low Space Storage Card (Flash)
Closed Closed YES No
2 Low Program Memory (RAM)
Closed Closed YES No
3 Temp-guard
Closed Closed YES No
4 Open Sensor Ch1 (RTD 1)
OPEN Closed YES YES
5 Open Sensor RTD 2
Closed Closed No No
6 Voltage Sensor Ch 2 (Humidity)
Closed OPEN YES YES
7 Voltage Sensor
Closed Closed No No
8 Voltage Sensor
Closed Closed No No
9 Voltage Sensor
Closed Closed No No
10 Hi Temperature
OPEN Closed YES YES
11 Low Temperature
OPEN Closed YES YES
12 Hi Humidity
Closed OPEN YES YES
13 Lo Humidity
Closed OPEN YES YES
14 Internal Comm. (Bad Data)
Closed Closed No No
15 Internal Comm. (Connection)
OPEN Closed YES YES
16 Olympic Board Reset
Closed Closed YES No
- 1.0 INTRODUCTION 6
- 2.0 SPECIFICATIONS 13
- UserAlarmS 16
- 2.3.1 Process Inputs 19
- 2.3.3 Channel Calibration 19
- 3.0 CHAMBER SAFETY 21
- SCREEN NAVIGATION KEYS 23
- 4.3 Touch Screen 24
- 4.4 LCD Screen 24
- 4.5 Function Keys 25
- 6.1 Setup Directory 34
- 6.2 Calibration 35
- 6.2.1 Channel Calibration 35
- 6.2.2 Altitude Calibration 38
- 6.2.3 Guaranteed Soak 38
- 6.2.4 Input Calibration 39
- Sensor Type 42
- A = a0 + a1 * T 43
- 6.3 PID 45
- PID \ SETUP DIRECTORY 45
- 6.3.1 PID Tuning 46
- 6.4 Special Functions 53
- 6.5 L - Values 59
- L – VALUES \ SETUP DIRECTORY 59
- 6.6 Settings List 62
- 6.8 LCD Settings 77
- 6.9 Chamber Setup 77
- Nano Temperature Only 82
- Nano Temperature Humidity 84
- Nano Thermal Shock 86
- Nano Temperature Pressue 88
- Nano Temperature Vibration 90
- Generic Temperature Only 92
- Generic Temperature/Humidity 96
- 2SM Outputs 100
- 3SM Event Outputs 100
- 1SM Outputs 100
- SSR Outputs 100
- Retro Temp Only 106
- 6.12 Logging 108
- LOGGING \ SETUP DIRECTORY 108
- 6.12.1 Logging Setup 109
- 6.13 Panel Lock 116
- 6.14 Languages 123
- LANGUAGES \ SETUP DIRECTORY 123
- 7.0 MAINTENANCE DIRECTORY 138
- 7.1 Operator Interface 139
- 7.2 Alarm Functions 144
- Modules 162
- 7.6 Clean Dat Utility 163
- 8.1 Operator Interface 165
- 8.1.1 RS-232 166
- 8.1.2 RS-485 166
- 8.1.3 IEEE 488 / GPIB 166
- 8.1.4 Ethernet 167
- 8.1.5 TCP/IP 167
- 8.1.6 WebTouch Remote ™ 167
- SUPPORTED CONTROLLERS 191
- 8.3.3 Ethernet MAC Address 192
- Page 193 193
- 8.3.4 Synergy FTP Server 196
- Page 200 200
- Page 202 202
- Page 206 206
- 9.3 Step Type Descriptions 211
- Temp Hum 213
- 9.6 Saving a Program 214
- 9.7 Running a Program 214
- 10.1 Main Screen 216
- 10.2 Entering a set point 216
- 10.2 Turn the chamber On 217
- 11.0 EVENTS SCREEN 218
- 11.1 Event Outputs Screen 219
- 11.3 Digital Outputs 223
- 11.4 Digital Inputs 225
- 12.0 GRAPH SCREEN 227
- 13.1 UUT Overview 228
- 13.2 Setup Procedure 230
- MODULE NO. 1 232
- INNER LOOP (AIR) 233
- OUTER LOOP 233
- CASCADE CONTROL 233
- 14.1 Cascade Control Setup 234
- Page 237 237
- 14.3 Using Cascade Mode 240
- 15.1 Space Chamber Setup 243
- Page 247 247
- 16.1 Synergy Nano Macros 251
- 16.3 Equipment 251
- 16.4 Installation 252
- 16.5 Controller Setup 255
- Saving the file as type CSV 256
- 17.2 Controller Mounting 262
- 17.3 Synergy Nano Wiring 264
- Pin TE1858‐1,2,3and4 264
- TE1858‐2 RelayOutputs 265
- TE1858‐3 SSROutputs 265
- 17.5.1 Ethernet Connection 272
- 17.5.2 RS-232 Connection 274
- 17.5.3 GPIB Connection 275
- Page 280 280
- Pins 9,10,11,12 289
- Connector P4 289
- Page 290 290
- Remove On-Board 290
- Triac when driving 290
- 17.8 Controller Setup 297
- 17.9 Alarm System Test 297
- Page 299 299
- Page 300 300
- Page 301 301
- Page 302 302
- Page 303 303
- Page 304 304
- Page 305 305
- Page 306 306
- Page 307 307
- Page 308 308
- Page 309 309
- Page 310 310
- Page 311 311
- Page 312 312
- Page 313 313
- Page 314 314
- Page 315 315
- Page 316 316
- Page 317 317
- Page 318 318
- Page 319 319
- Page 320 320
- Page 321 321
- Page 322 322
- Page 323 323
- Page 324 324
- Page 325 325
- Page 326 326
- Page 327 327
- Page 328 328
- Page 329 329
- Page 330 330
- Page 331 331
- Page 332 332
- Page 333 333
- Page 334 334
- Page 335 335
- 18.2 SimpleComm Examples 336
- 18.4 LabVIEW ™ Driver 342
- Page 347 347
- Page 352 352
Related products and manuals for Vacuum cleaners Simplicity Synergy X9
(6 pages)© 2020, manymanuals.com. All rights reserved. | 1.233 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals